Response deadlineSep 18, 2026, 8:30 PM UTC
Deadline status15 days remaining
PostedAug 18, 2026
Record refreshedSep 2, 2026
Place of performanceAnniston, AL, 36201, United States
Opportunity summary
Source-citedThis solicitation from the Department of Defense is for a Valve, Linear, Direct (NSN: 4810-01-201-4843), with an amendment increasing the quantity to 121 units. Responses are due on September 18, 2026, and the place of performance is Anniston, AL. [3]
Key points
- Amendment increased quantity for CLINs 0001AA and 0002AA to 121 ea. [3]
- Prime Contractor must maintain detailed process control plans and testing. [1]
Watch items
- No set-aside is used for this opportunity. [3]
- Proposal submission size and content may be factors. [2]
Sources
- SPRDL126Q0040.pdf
This information shall be available upon Government request. (3) The prime Contractor shall immediately notify the PCO and the Defense Contract Management Agency (DCMA) of any failure to meet preproduction and production requirements. (4) Each cleaning method shall be treated as a separate step in the process documentation. (5) The Gage Repeatability and Reproducibility (Gage R&R) error shall be less than 30 percent for all process and product 15 55 SPRDL1-26-Q-0040
- SPRDL126Q0040.pdf
Note: There is no "expected" or "target" length of time for proposal submission; size and content may be factors, therefore offerors are strongly cautioned when submitting proposals to allow adequate time for submission.
- Official SAM.gov notice
Set-aside: No Set aside used
Generated from the public notice and source-backed solicitation passages. Confirm important requirements in the cited brief and official documents.
Public-source intelligence
Source-backed opportunity brief
This information shall be available upon Government request. (3) The prime Contractor shall immediately notify the PCO and the Defense Contract Management Agency (DCMA) of any failure to meet preproduction and production requirements. (4) Each cleaning method shall be treated as a separate step in the process documentation. (5) The Gage Repeatability and Reproducibility (Gage R&R) error shall be less than 30 percent for all process and product 15 55 SPRDL1-26-Q-0040
Scope
The requirements in this clause clarify and supplement those in the contract, unless nullified elsewhere in the contract or through an approved Request for Deviation. (2) Coating qualification, spot paint repair, and MIL-DTL-16232 Phosphate Coating, Heavy, Manganese or Zinc Base coatings are not within the scope of this clause. (b) Definitions (1) The "contracting agency," "appropriate agency," "procuring authority," "engineering authority," "procuring agency," and "procuring activity" is the PCO or designee. (2) The "prime Contractor" is the company awarded this contract, and the "subcontractors" comprise all companies involved in providing coated parts to the prime Contractor, including companies that apply the coatings. (c) General Requirements Clarifications (1) The Government retains the right for onsite verification of the prime Contractor's and its subcontractors' products, processes, procedures, and test reports. (2) The prime Contractor shall be responsible for itself and its subcontractors to produce and maintain detailed process control plans, process control data, pre-production approval testing, ongoing quality control & quality control testing, and test reports.
Deliverables
Invoice and Receiving Report (B) For services that do not require shipment of a deliverable, submit either the Invoice 2in1, which meets the requirements for the invoice and receiving report, or the applicable invoice and receiving report, as specified by the Contracting Officer.
Evaluation
These prices will be used in conjunction with the evaluation factors stated elsewhere in the solicitation in order to make the award decision in accordance with the basis for award stated in the solicitation.
Submission
Note: There is no "expected" or "target" length of time for proposal submission; size and content may be factors, therefore offerors are strongly cautioned when submitting proposals to allow adequate time for submission.
Eligibility
Set-aside: No Set aside used
Place of performance
Anniston, AL, 36201, USA
Key dates
Posted Aug 18, 2026; Responses due Sep 18, 2026, 8:30 PM UTC; Archive date Dec 31, 2026
Extracted from the official notice and archived solicitation files. Confirm controlling requirements in the source documents.