DEPT OF DEFENSE · DEPT OF THE ARMY · W7M2 USPFO ACTIVITY FL ARNG
The Department of Defense seeks a life cycle replacement for a telescopic mast for the AMRT, requiring specific technical capabilities like a 20-foot extended height and 200 lbs payload support. The solicitation is a Small Business Set Aside, with a response deadline of September 14, 2026. [3]
If WAWF is not required by this contract, and the contractor is not using WAWF, follow the procedures at http://dodprocurementtoolbox.com/site/uidregistry/. (2) Embedded items shall be reported by one of the following methods- (i) Use of the embedded items capability in WAWF; (ii) Direct data submission to the IUID Registry following the procedures and formats at http://dodprocurementtoolbox.com/site/uidregistry/; or (iii) Via WAWF as a deliverable attachment for exhibit line item number (fill in) ____, Unique Item Identifier Report for Embedded Items, Contract Data Requirements List, DD Form 1423. (g) Subcontracts.
The use in this solicitation of any ( (b) Defense Federal Acquisition Regulation 48 CFR ) provision with an authorized deviation is indicated by the addition of "(DEVIATION)" Chapter 2 after the name of the regulation. (End of provision) W911YN26QA026 Page 35 of 37 Section M - Evaluation Factors for Award BASIS FOR AWARD ***Addendum to 52.212-2*** 1.0 Evaluation of offer will be performed using one or more of the techniques in FAR 12.203.
Set-aside: Small Business Set Aside - Total
Generated from the public notice and source-backed solicitation passages. Confirm important requirements in the cited brief and official documents.
The contractor shall use an automatic identification technology device for this verification that has been programmed to the requirements of Appendix A, MIL-STD-130, latest version. (ii) The issuing agency code- (A) Shall not be placed on the item; and (B) Shall be derived from the data qualifier for the enterprise identifier. (d) For each item that requires item unique identification under paragraph (c)(1)(i), (ii), or (iv) of this clause or when item unique identification is provided under paragraph (c)(1)(v), in addition to the information provided as part of the Material Inspection and Receiving Report specified elsewhere in this contract, the Contractor shall report at the time of delivery, as part of the Material Inspection and Receiving Report, the following information: (1) Unique item identifier. (2) Unique item identifier type. (3) Issuing agency code (if concatenated unique item identifier is used). (4) Enterprise identifier (if concatenated unique item identifier is used). (5) Original part number (if there is serialization within the original part number). (6) Lot or batch number (if there is serialization within the lot or batch number). (7) Current part number (optional and only if not the same as the original part number). (8) Current part number effective date (optional and only if current part number is used).
COMBO (B) For services that do not require shipment of a deliverable, submit either the Invoice 2in1, which meets the requirements for the invoice and receiving report, or the applicable invoice and receiving report, as specified by the Contracting Officer.
If WAWF is not required by this contract, and the contractor is not using WAWF, follow the procedures at http://dodprocurementtoolbox.com/site/uidregistry/. (2) Embedded items shall be reported by one of the following methods- (i) Use of the embedded items capability in WAWF; (ii) Direct data submission to the IUID Registry following the procedures and formats at http://dodprocurementtoolbox.com/site/uidregistry/; or (iii) Via WAWF as a deliverable attachment for exhibit line item number (fill in) ____, Unique Item Identifier Report for Embedded Items, Contract Data Requirements List, DD Form 1423. (g) Subcontracts.
The use in this solicitation of any ( (b) Defense Federal Acquisition Regulation 48 CFR ) provision with an authorized deviation is indicated by the addition of "(DEVIATION)" Chapter 2 after the name of the regulation. (End of provision) W911YN26QA026 Page 35 of 37 Section M - Evaluation Factors for Award BASIS FOR AWARD ***Addendum to 52.212-2*** 1.0 Evaluation of offer will be performed using one or more of the techniques in FAR 12.203.
The offeror is cautioned that the listed provisions may include blocks that must be completed by the offeror and submitted with its quotation or offer.
Set-aside: Small Business Set Aside - Total
Saint Augustine, FL, 32086, USA
Posted Aug 31, 2026; Responses due Sep 14, 2026, 9:00 PM UTC; Archive date Sep 29, 2026
Extracted from the official notice and archived solicitation files. Confirm controlling requirements in the source documents.
Product Description TELESCOPING MAST PRODUCT DESCRIPTION The FLNG-CDP requires a life cycle replacement for a critical component of the YF309J, Trailer, Special Purpose-the primary telescopic tower utilized by the Air and Marine Reconnaissance Team (AMRT) during reconnaissance and observation (R&O). AMRT seeks a commercial off the shelf platform that provides next generation command and control (NGC2), on the move (OTM) and at the halt (ATH) capabilities. The desired platform must meet the following capabilities: - Base tube diameter is not more than seven inches. - No more than 6 mast sections. - Retracted height no more than 70 inches, with an extended mast height of 20 feet. - Total mast weight under 205 lbs. - Mast must support 200 lbs. payload. - MIL-STD-810 tested aluminum and stainless-steel construction. - Manual winch with self-lubricating shims. - Upper and lower electro-mechanical safety switches. - Custom mast head adaptor for various sensors. - Cable guide rings on each mast section. - Tool-less accessories to simplify set up and storage. - Extended wall mount to attach mast to Mobile Operations Command Trailer. - Drainage ports.
No field-level changes were detected between related notices.
Open a filename to view the saved source file. If a saved copy is not available yet, FedRoster will continue to the matching SAM.gov notice.